Fleet Management News & Business Info | Commercial Carrier Journal
Issue link: http://read.uberflip.com/i/493405
66 COMMERCIAL CARRIER JOURNAL | APRIL 2015 TRAILER FOCUS DRY VANS CHAMPION SE LENGTH: 53 ft. WIDTH: 102.36 in. HEIGHT: 13.6 ft. SIDES: 1.1-in. steel hat section uprights on 24-in. centers; logistics posts optional; 0.05-in. prepainted white flat corrugated aluminum side sheets ROOF: 0.04-in. aluminum sheet with bows on 24-in. centers REAR DOORS: 0.5-in. composite swing; dual-seal gaskets; white gal- vanized steel cover sheet FLOOR: 1.38-in. laminated hardwood CROSSMEMBER: Front – steel hat type for tire protection between support gear and coupler; bay and side areas – 4-in.-deep steel I-beams on 12-in. centers SUSPENSION: Holland DuraLite LS4 sliding air ride with 49-in. axle spacing; spindle axle ANTI-LOCK BRAKES: Meritor Wabco 2S/1M Easy Stop BRAKES: 16.5-by-7-in. drums with S-cam brakes SCUFF BAND: 12-in. galvanized 18-gauge steel, full length INTERIOR OPTIONS: Overlaid track; various scuff bands; aluminum cargo floors; interior and ceiling linings HYUNDAI TRANSLEAD | www.translead.com HT ORIGINAL LENGTH: 53 ft. WIDTH: 102.36 in. HEIGHT: 13 ft. 6 in. SIDES: 0.05-in.-thick prepainted white aluminum ROOF: One-piece 0.04-in.-thick full- width aluminum sheet, tension-leveled prior to installation REAR FRAME: Hot-dipped 0.375-in.-thick galvanized steel construction with low-profile header, tube-shaped posts; forged steel angle iron in top corners for added rack resistance; lights recessed in rear sill with heavy-duty protection bars CROSSMEMBER: 4-in.-deep hot-rolled steel I-beam; 80,000-psi yield strength, located on 12-in. centers; hat-shaped crossmembers ahead of landing gear; rear 4 ft. of trailer has crossmembers located on 8-in. centers SUSPENSION: Hendrickson Vantraax HKANT 40K Air Ride ANTI-LOCK BRAKES: Two-sensor/one-modulator valve 2S/1M system, PLC4Trucks-compatible system BRAKES: Nonasbestos lining, 16.5-by-7-in. quick-change type; S cam- operated automatic slack adjuster INTERIOR LINING: Exterior-grade 0.25-in. plywood installed horizontally over side posts; exterior-grade 0.5-in. plywood installed on bottom, 0.25-in. on top over front wall HT HY-CUBE LENGTH: 53 ft. WIDTH: 102.36 in. HEIGHT: 13 ft. 6 in. SIDES: 0.05-in.-thick pre- painted white aluminum ROOF: One-piece 0.04-in.-thick full-width aluminum sheet, tension- leveled prior to installation REAR FRAME: Hot-dipped 0.375-in.-thick galvanized steel construction with low-profile header, tube-shaped posts; forged steel angle iron in top corners for added rack resistance; lights recessed in rear sill with heavy-duty protection bars CROSSMEMBER: 4-in.-deep hot-rolled steel I-beam; 80,000-psi yield strength, located on 12-in. centers; hat-shaped crossmembers ahead of landing gear; rear 4 ft. of trailer has crossmembers located on 8-in. centers SUSPENSION: Hendrickson Vantraax HKANT 40K Air Ride ANTI-LOCK BRAKES: Two-sensor/one-modulator valve 2S/1M system, PLC4Trucks-compatible system BRAKES: Nonasbestos lining, 16.5-by-7-in. quick-change type; S cam- operated automatic slack adjuster INTERIOR LINING: White 0.235-in.-thick HDPE lining installed full height between uprights with no fasteners; side lining hooks into place for easy replacement; exterior-grade 0.50-in. plywood installed on bottom, 0.25-in. on top over front wall HT COMPOSITE/XT LENGTH: 53 ft. WIDTH: 102.36 in. HEIGHT: 13 ft. 6 in. SIDES: 0.25-in.-thick composite panel with prepainted white high-tensile galvanized steel inner and outer sheets ROOF: One-piece 0.04-in.-thick full-width aluminum sheet, tension- leveled prior to installation REAR FRAME: Hot-dipped 0.375-in.-thick galvanized steel construction with low-profile header, tube-shaped posts; forged steel angle iron in top corners for added rack resistance; lights recessed in rear sill with heavy-duty protection bars CROSSMEMBER: 4-in.-deep hot-rolled steel I-beam; 80,000-psi yield strength, located on 12-in. centers SUSPENSION: Hendrickson air ride ANTI-LOCK BRAKES: Two-sensor/one-modulator valve 2S/1M system, PLC4Trucks-compatible system BRAKES: Nonasbestos lining, 16.5-by-7-in. quick-change type; S cam- operated automatic slack adjuster INTERIOR LINING: Exterior-grade 50-in. plywood installed on bottom, 0.25-in. plywood installed on top over front wall, none on sidewalls