Issue link: https://read.uberflip.com/i/559169
132 FEATURES AND SPECIFICATIONS Circular Industrial ™ Connectors Spirit ™ Technical Specifications Agency Approvals National Electric Code: Spirit connectors conform to the NEC if applied within the constraints of the code. Underwriters Laboratories: Spirit series connectors are recog- nized under the Underwriters Laboratories Component Recognition Program. File No.: E81982 (N). Canadian Standards Association: Spirit series connectors are certified by CSA under File No.: LR56804-1, -2, -3. Spirit conforms to the JIC and Machine Tool Standard NFPA79 Spirit meets NEMA 4X, enclosure requirements. Spirit 600V inserts meet the spacing requirements of VDE (3mm through air, 4mm over surface) Mechanical Cord Strain Relief: 35 lb min. throughout range per UL 514. Spirit values exceed 100 lb on most applications (50 lb with sleeve glands). Metallic Liquid-Tight Conduit Strain Relief: 150 lb min. per UL 514 for Type M Termination Crimp Strengths: Spirit values exceed UL 486 for all wire gauges specified Mating Cycles: 500 mate/unmate cycles without excessive wear Shock: 50 G min., all planes. Coupling nut is spring loaded to resist impact damage Vibration: Complies with MIL STD 202F, Test Method 204, Test Condition B. Coupling nut is spring loaded to resist loosen- ing under vibration. Electrical Voltage: Each insert is stated as AC/DC values Current: Determined by the bulk temperature rise, including ambient, not exceeding the insert temperature rating which is 90°C. In general, the connectors are capable of carrying the currents of the SO Cable they are designed to accommodate. The NEC Tables on Current Ratings of Wires in Conduit also may be used as a reference to allowable currents. In specific applications larger currents may be adequately handled by a few circuits without difficulty, but in no instance should more than the following maximums be applied to the terminals: Contact the factory for advice if the application is question- able. In no instance should the bulk temperature exceed 90°C including ambient when maximum current is applied. All ratings apply to applications where the connector is not dis- engaged under load. Dielectric Withstanding Voltage: Conforms to UL 498. Tested at 1000V plus twice rated voltage for 1 minute between ter- minals and terminals to the shell. Insulation Resistance: 5000 M1 typical at 25°C, 40 to 60% relative humidity Millivolt Drop: Voltage probes located 1/4" away from crimp barrel Environmental Temperature: -40 to +194°F Humidity: 100 M1 min. insulation resistance after 96 hours of 95 to 100% relative humidity at 100°C (MIL STD 202F Test Method 103B Condition B) Moisture Seals: No water enters electrical chamber when sub- jected to water spray per UL 514. Dust caps afford addi- tional seal protection as well as preventing entry of mud, chips and other debris. Corrosion: No exposure of base metal evident after 500 hours in salt spray per MIL STD 1344. Shells are inert to most caustics. Hard-coat finish is approved for offshore marine duty. Chemical Resistance: Inserts impervious to most oils, alcohols, fuels, glycols, salts, soaps and mild alkalis. Contact factory for specific applications. Terminal No. Wire AWG Current (Amperes) mV Drop 16 Tin 16 1.0 1.5 20 Gold 20 1.0 3.1 Terminal No. Absolute Maximum Current 8 50A 10 or 12 35A 14 or 16 15A 18 or 20 10A Current Ratings Min. (Amperes) — All Circuits Terminal Size Circuits 8 10 12 14 16 18 20 2 40 30 25 18 13 10 7 3 40 25 20 15 10 7 5 4-6 35 20 16 12 8 6 4 7-24 17.5 14 10.5 7 5 3.5 25-42 15 12 9 6 4 3 43+ 12.5 10 7.5 5 3.5 2.5 Molex Industrial Division New England Operations Gilford, NH Phone (603) 524-5101 Fax (603) 524-1627 Ulti-Mate Connector Inc. 1872 North Case Street Orange, Ca 92865 www.umi-c.com T : 714-637-7099 F : 714-637-7464 2